Codice: Seleziona tutto
set 09 17:54:45 keplero kernel: blk_update_request: critical target error, dev sdd, sector 3907026816 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
set 09 17:54:45 keplero kernel: sd 6:0:0:0: [sdd] tag#1 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE cmd_age=0s
set 09 17:54:45 keplero kernel: sd 6:0:0:0: [sdd] tag#1 Sense Key : Hardware Error [current]
set 09 17:54:45 keplero kernel: sd 6:0:0:0: [sdd] tag#1 Add. Sense: Internal target failure
set 09 17:54:45 keplero kernel: sd 6:0:0:0: [sdd] tag#1 CDB: Read(10) 28 00 e8 e0 7f 80 00 00 08 00
set 09 17:54:45 keplero kernel: blk_update_request: critical target error, dev sdd, sector 3907026816 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
set 09 17:54:45 keplero kernel: Buffer I/O error on dev sdd1, logical block 488378096, async page read
set 09 17:54:52 keplero kernel: usb 3-7: USB disconnect, device number 5
set 09 17:54:52 keplero kernel: sd 6:0:0:0: [sdd] Synchronizing SCSI cache
set 09 17:54:52 keplero kernel: sd 6:0:0:0: [sdd] Synchronize Cache(10) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
set 09 17:54:56 keplero kernel: usb 3-8: USB disconnect, device number 7
set 09 17:54:56 keplero kernel: xpad 3-8:1.0: xpad_try_sending_next_out_packet - usb_submit_urb failed with result -19
Codice: Seleziona tutto
$ sudo smartctl --all -d sat /dev/sdd
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.13.12-200.fc34.x86_64] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 2.5 5400
Device Model: ST2000LM015-2E8174
Serial Number: WDZT23Z6
LU WWN Device Id: 5 000c50 0d54c6f1d
Firmware Version: 0001
User Capacity: 2.000.398.934.016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
TRIM Command: Available
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Sep 9 18:10:03 2021 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x71) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 319) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 083 065 006 Pre-fail Always - 213463526
3 Spin_Up_Time 0x0003 099 099 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 56
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 061 060 045 Pre-fail Always - 1160644
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 252 (116 219 0)
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 25
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 068 057 040 Old_age Always - 32 (Min/Max 32/34)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 9
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1148
194 Temperature_Celsius 0x0022 032 043 000 Old_age Always - 32 (0 23 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 17 (86 56 0)
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 2142658362
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 1005540756
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
